PS Audio




Hand-crafted, high-end home music reproduction systems designed, engineered and built by people that care: about lifestyle, music, the environment, quality, fairness and the trust the PS Audio has earned over the last 40 years.

Click here to view the product range


$4,499.00
BUY NOW

A powerful full sized affordable mono power amplifier honoring the music and controlling your loudspeakers better than you imagined possible. From the deepest bass to the warmest, sweetest highs, the Stellar M700 takes control and...

Features
Tech Specs
  • Mono power amplifier pair
  • Zero-loss Analog Cell input stage
  • Powerful MOSFET balanced output stage
  • RCA Single ended input
  • XLR true balanced input
  • 350 watts into 8?
  • 700 watts rms into 4?
  • 2? stable
  • Less than 0.1% thd 20Hz to 20kHz at rated power
  • Damping factor 200 for excellent loudspeaker control
  • Front panel standby button
  • Effieicient operation with very little heat
  • Dual, solid copper, plated, output binding posts
  • 27 pounds
  • Input 12 volt trigger
$2,299.00
BUY NOW

Finally, a full sized affordable power amplifier that honors the music and controls your loudspeakers better than you ever imagined possible. From the deepest bass to the warmest, sweetest highs, the Stellar S300 makes any loudspe...

Features
Tech Specs

Rated at 140 Watts per channel into 8? and 300 Watts per channel into 4?, the S300 combines the best of two worlds: ultra linear, high-current, Class D technology for the output stage; a discrete, Class A MOSFET based Analog Cell for the all-important input stage. The S300s rich, warm, and engaging sonic character comes from the Analog Cell. Its powerful, authoritative control over the loudspeaker stems from its high current, ultra-low impedance Class D output stage.

Unit Weight 13 lbs
Unit Dimensions 17 x 3 x 12 Chassis only. 13" deep including connectors.
Shipping Weight 16.5 lbs
Shipping Dimensions 22x 8 x 17
Color Options Black
Silver
Voltage Options
Factory set only
Japan 100V
North America 120V
Europe/Asia/Australia/New Zealand 230V
Mains Power Inputs IEC C14
Accessories Included US (NEMA 5-15P) (all versions)
Schuko (CEE7/7) (230V version)
UK (BS 1363) (230V version)
Audio Inputs RCA (Unbalanced)
XLR (Balanced)
Speaker Outputs S300 Copper base nickel plated binding posts (2 pair per channel)
Speaker Outputs M700 Copper base nickel plated binding posts (2 pair)
Other DC Trigger Input
3.5mm 5-15VDC
Warranty 3 years parts and labor

Signal

 
Gain 30.5dB +/-0.5dB
Sensitivity for rated output power 1.01V
Noise 1kHz@300 Watts <-100dB
Input impedance S300 Unbalanced 50K?
Balanced 100K?
Input impedance M700 Unbalanced 50K?
Balanced 100K?
Output Impedance 50Hz, 2.8VRMS <0.007?
Damping factor 50Hz. 2.8VRMS
8? >1100
4? >550
Frequency Response @2.8VRMS
10Hz 20KHz +/- 0.5dB
10Hz 50KHz +0.1/-3.0dB

THD&IM

 
1KHz, 1W/4? <0.02%
10-20KHz, 1W/4? <0.02%
10-50KHz, 1W/4? < 0.05% (90kHz BW)
1KHz, 37.5W/4? < 0.01%
   

S300 Stereo Amplifier

 

Output Power

Both channels driven 120vac mains, 1kHz, 1% THD
8? 140W minimum
4? 300W minimum
2? Stable for musical transients

M700 Mono Amplifier

 

Output Power

120vac mains, 1kHz, 1% THD
8? 350W minimum
4? 700W minimum
2? Stable for musical transients
$2,599.00
BUY NOW

The best of two worlds. A full-featured state of the art DAC combined with a rich zero loss analog preamplifier in one chassis. Just connect a power amplifier for a complete no-compromise system. ...

Features
Tech Specs

At the heart of Stellar Gain Cell DAC is a stunning, Bob Stadtherr designed, digital to analog converter. Based on industry leading Sabre32 bit Hyperstream architecture, Stellar DAC features a fully balanced Class A analog output stage with multiple power supplies, independent jitter-reduced inputs, DSD, I2S, and asynchronous USB.

The DACs output level is controlled by the analog Gain Cell. Developed in the early 2000s by PS Audio founder Paul McGowan, the Gain Cell elegantly solves the fundamental problem facing preamp designers. Volume control. Nearly all analog preamplifiers use additional sonically-degrading elements inserted in the signal path to control volume. These impediments to the signal paths purity range from simple potentiometers to exotic stepped attenuators, relays, solid state switches, ladder networks, transformers, light dependent resistors. All share intrusive elements in the signal path. The Gain Cell eliminates this problem without additional circuitry in the signal path by varying its gain in response to front panel controls.

  • Class A balanced analog preamplifier
  • Full function DAC
  • Class A headphone output
  • Remote control
  • Fixed or variable DAC mode
  • 2 output 12 volt triggers

Analog preamplifier

  • One balanced analog input
  • Three single ended analog inputs
  • Analog Gain Cell stage
  • Fully balanced input to output
  • Balanced XLR analog output
  • Single ended RCA analog output
  • Home theater bypass
  • Direct coupled without any capacitors in output signal path

Digital To Analog Converter

  • Four digital inputs
  • I2S input
  • Digital Lens technology
  • Native Mode
  • Three user selectable digital filters
  • Compatible with PS Audio DMP for SACD playback in DSD
  • DSD direct through I2S
  • 192kHz asynchronous coax input
  • 192kHz asynchronous USB
  • 96kHz asynchronous TOSLINK input
  • Single and double rate DSD
  • CPLD input (FPGA) lowers jitter, waveshapes, reduces propagation delay
  • Native mode standard
  • No added Sample Rate Conversion
  • High current class A hybrid output stage
  • Passive output filter lowers transient distortion
  • Direct coupled without any capacitors in output signal path
  • High bandwidth output stage -3dB 60kHz
  • Low jitter clocks
  • High Current oversized analog power supply
  • 7 voltage regulators
  • High speed power supply diodes
  • Massive 15,000 mFd low ESR capacitors
  • ESS Hyperstream
$22,698.00
BUY NOW

We have a one-off package deal available for a BHK Preamplifier and 250 Power Amplifier pair. Only one set available! More information on the BHK Preamp here and the BHK 250 Power Amp here. ...

Features
Tech Specs
$6,499.00
BUY NOW

Introducing DirectStream Junior, a world class DAC based on the architecture of the Stereophile and Absolute Sounds Product Of The Year, DirectStream. Hand-written, discrete, perfection based conversion that uncovers all the...

Features
Tech Specs

Pure 100% single bit DSD based D to A Converter
Passive/active output stage
Resolution perfect volume and balance controls
Simple, direct signal path with only one master clock
High immunity to jitter from sources
Asynchronous high speed USB and Network access
Polarity inversion
Play directly into your power amplifier or preamplifier
Hear more than you ever imagined from CDs

Physical

 
Unit Weight 18 lbs [8.1 kg]
Unit Dimensions 14 x 17 x 2.75 [ 36cm x 43cm x 6.98cm]
Shipping Weight 27 lbs [12.25 kg]
Shipping Dimensions 20.5x 24 x 10 [52cm x 61cm x 25cm]

Power requirements

 
Input Power Model specific 100VAC, 120VAC, or 230VAC 50 or 60Hz
Power Consumption 30W

Digtial audio inputs

IS, Coax, XLR Balanced, TOSLINK, USB, Ethernet

Sample Rates

IS,S/PDIF, and USB -- 44.1kHz to 352.8kHz 16bit, 24bit, DSD 64, DSD 128
TOSLINK 44.1kHz to 96kHz 16bit, 24bit

Analog Audio Output

 
Connector RCA/XLR Unbalanced /Balanced (X2)
Output level, low 1.41 Vrms(+5BV)/3.15
Output level high, maximum 2.81 Vrms (+8dBV)/5.3 Vrms (+12dBV)
Output Impedance 100?/200?
Frequency Response 20-20KHz +/- 0.25dB
THD+N @ 1KHz (full scale) <0.03%
Output Stage Active high current, high speed analog amps producing double rate DSD.

Data Handling

 
Format PCM or DSD
Sample rate (PCM) 44.1kHz, 48.0kHz, 88.2kHz, 96.0kHz, 176.4kHz, 192kHz, 352.8kHz
Word length (PCM) 16b, 18b, 20b, 24b
Data rate (DSD) Standard (2.8MHz) or Double (5.6MHz) DoP on all inputs as well as raw DSD on IS inputs
Input jitter reduction Effectively 100%, residual immeasurable. No input PLLs, FLLs.
Input Processing 170MHz
Signal Processing 50MHz
Synchronous Upsampling, all inputs 28.224MHz
Digital Processing S/N ration >146 dB
Digital Volume Control Zero loss of precision
Analog Conversion method Delta Sigma (DSD) Single-bit double rate

IS Digital Input

 
Connector HDMI
Format PCM or DSD. DoP on all inputs as well as raw DSD on IS inputs

USB Digital Input

 
Connector USB B Type
Format PCM or DoP v1.1 (DSD over PCM)
Transfer mode Asynchronous
$12,999.00
BUY NOW

The BHK Signature 250 and 300 power amplifiers are the culmination of one mans half-century search for perfection in musics reproduction. Bascom H. King has designed amplifiers for many companies, some selling in excess of ...

Features
Tech Specs

BHK Signature 250 Stereo and BHK Signature 300 Mono

 
Unit Weight 83 lbs
Unit Dimensions 17.1 x 8.7 x 14 Chassis only. 15" deep including connectors.
Shipping Weight 92 lbs
Shipping Dimensions 21x 13 x 19
Color Options Black
Silver
Voltage Options
Factory set only
Japan 100V
North America 120V
Europe/Asia/Australia/New Zealand 230V
Mains Power Inputs IEC C14
Fuse Compliment all Countries 4 - 10 amp fast blow H-Rated 5x20mm Rail Fuses
Fuse Compliment Mains 100vac Countries
1 - 2 amp slow blow H-rated 5x20mm
1 - 12 amp slow blow H-rated 5x20mm
120vac Countries
1 - 1.6 amp slow blow H-rated 5x20mm
1 - 10 amp slow blow H-rated 5x20mm
230vac Countries
1 - 1 amp slow blow H-rated 5x20mm
1 - 5 amp slow blow H-rated 5x20mm
Accessories Included US (NEMA 5-15P) (all versions)
Schuko (CEE7/7) (230V version)
UK (BS 1363) (230V version)
Audio Inputs RCA (Unbalanced)
XLR (Balanced)
Speaker Outputs Signature 250 Gold plated copper binding posts (2 pair per channel)
Speaker Outputs Signature 300 Gold plated copper binding posts (2 pair)
Other DC Trigger Input 
3.5mm 5-15VDC
Warranty 3 years parts and labor on unit
1 year on vacuum tube

Power Consumption

 
@Ready 75 Watts
@Idle 175 Watts
@Rated power 8? 850 Watts
@Rated power 4? 1600 Watts

Signal

 
Gain 30.5dB +/-0.5dB
Sensitivity 1.2V
Noise 100-20KHz <-85dBV
Input impedance Unbalanced 100K?
Balanced 200K?
Output Impedance 50Hz, 2.8VRMS <0.1?
Frequency Response @2.8VRMS
10Hz 20KHz +/- 0.1dB
10Hz 200KHz +0.1/-3.0dB

THD

 
1KHz, 1W/8? <0.01%
20-20KHz, 1W/8? <0.1%
1KHz, 200W/8? < 0.1% (120VAC Mains input)
1KHz, 400W/4? < 0.1% (120VAC Mains input)
   

Signature 250 Stereo Amplifier

 

Output Power

Both channels driven 120vac mains, 1kHz, 1% THD
8? 250W minimum
4? 500W minimum
2? Stable for musical transients

Signature 300 Mono Amplifier

 

Output Power

120vac mains, 1kHz, 1% THD
8? 300W minimum
4? 600W minimum
2? 1000W
$7,499.00
BUY NOW

The PS Audio PerfectWave MKII is a remarkable new class of productthat makes high-end music fun again. It accesses high-resolution digital audio data, CD transports and players, computers, home networks, or the Internet and con...

Features
Tech Specs

A built in Digital lens

The MKII features our exclusive Digital Lens technology built right inside. The Digital Lens takes any digital audio signal and regenerates a new and jitter free version to listen to.

The Digital Lens, called NativeX, is selectable from the front panel or the remote. Engaging NativeX will reduce incoming jitter levels jitter on any input of the PWD to below 1 pico second, regardless of how jittered the incoming signals are.

The digital lens improves sound quality in the MKII so dramatically that I consider the MKI product broken. Honestly I cant imagine listening to a PerfectWave DAC without sending every bit of audio through the sharp focus of the Digital Lens

Asynchronous high speed USB

A Media DAC, like the PerfectWave, can match up to either a computer or a home network. The PWD can do both with the Network Bridge installed. For those customers connecting to their computer without the Network Bridge, theres USBavailable. USB communication, if handled properly, can have every sound quality advantage of a dedicated CD transport or Network Bridge.

New in the MKII is a completely redesigned high-resolution USB path. Asynchronous and capable of 24 bit 192kHz performance, the new USB input sounds every bit as good as the best digital audio. Finally, computer audio without limitations and compromise to the sound quality and its all yours in the new MKII. Using a high quality USB cable between the PWD and computer, like a quiet MAC Mini, and you have an instant media server that can be controlled through any number of hand held devices like an iPod, iPhone or Android using a 3d party controller program. Your music can be managed by iTunes or Ammara for ease of use.

11 power supplies

The MKII has 11 separately regulated power supplies for best performance. Each of the 11 supplies is a super low noise design placed strategically around the digital processing board to lower noise, jitter and talk-back. Properly designed power supplies are like one way gates that provide a clean and plentiful source of needed power to each section of a circuit, while keeping out unwanted noise, jitter and potentially degrading artifacts generated in digital audio circuits.

The results of these low noise power supplies are quite noticeable- mostly as an openness that simply wasnt present in older designs. On larger orchestral pieces of music, individual instruments take on increased air and separation between each of the players.

Lower jitter clocks

Digital clocks are an essential element to a digital audio DAC. They play a significant role in audio performance that can ranging from poor to spectacular depending on how they are implemented. Clocks can be either fixed or variable frequency devices depending on the design, but fixed clocks outperform variable clocks and these are what PS Engineering depend on to set the critical timebase in the PWD MKII.

Our fixed clocks have extremely low jitter and provides a stable reference for the digital audio data. In addition to lowered jitter and improved stability, each of the internal clocks in the MKII benefits from its own power supply that keeps the clock isolated from all other timing devices in the circuit.

The results from lowered jitter isolated clocks are audibly cleaner upper harmonics and a reduction in digital glare, present on more jittered electronics.

Balance control

It hasnt escaped us that many of our customers rely on the PerfectWave DAC as their primary music source feeding a power amplifier directly. In fact, that is our preferred method of connection. Many preamplifiers only add an extra layer of unwanted veiling and restricted dynamics to the sound. Unfortunately the MKI had no provision for adjusting the balance between the left and right channel, thus any mismatched loudspeaker pair or unequal room acoustics contributed to a slight skewed image when using the PWD directly.

The MKII solves that problem with a balance control, capable of shifting the balance between left and right in small 1/10th of a dB increments adjustable from the new (and supplied) remote control.

You view the changes in balance from the PWDs touch screen and everything can easily be handled from the comfort of your listening position.

Analog switching in the digital audio path

If you were able to view digital audio moving through a circuit board it would remind you of a busy city with hundreds of intersections, stop lights, and a maze of streets. The digital traffic is directed and routed through devices known as digital switch gates and these play a large role in audio quality.

The vast majority of digital switch gates use a type of transistor logic that is known as saturated logic. This simply means that when the gate is in the fully on state, it is locked or saturated on. When it moves from this saturated on-state to its off-state, the point of transition can vary from device to device causing jitter and poor sound.

The MKII uses high-speed analog switches instead of saturated logic digital switches. CMOS analog switches do not go into saturation mode, do not add jitter or timing issues and sound remarkably better than anydigitallogic gate weve auditioned.

Low noise layout and spot regulators

Digital audio noise is one of the most difficult issues to lower in a complex digital circuit. Techniques include multi-layer PC boards, precision trace lengths for digital audio signals and spot regulation using localized power regulators at strategic points in the circuit.

Execution of the circuit board is the key to a low noise design and the MKII has all these considerations in spades. PS Engineers cleaned the decks, rolled up their sleeves and created an entirely new design for the digital processing board from scratch. Special attention was paid to a low noise design that included the addition of 11 new spot regulators, matched and measured PCB traces in critical areas to minimize reflections and maintain proper impedances and superior capacitive bypass techniques using low ESR capacitors in critical areas.

The MKII digital processing board has 10dB lower emitted radiated digital noise than its predecessor, the MKI and this lowered noise is due entirely to careful design, spot regulation and matched traces in critical areas.

Minimum phase and apodizing filters

All DACS and digital media servers rely on filters to cleanup the audio and help make the music sound open and natural. The qualities of these filters has a great deal of impact on how the music sounds through your system.

The PWD MKII utilizes the best sounding apodizing and phase correct filters, selectable from the front panel touch screen or through the supplied IR remote control.

The MKII provides 5 filter choices, each automatically memorized on a per input basis. So, for example, if your CD transport benefits from Filter 1 and your Bridge sounds best with filter 2, the selected filter will automatically engage along with the choice of input.

In addition to hand selecting the various filters you can let the MKII make the choice for you with the Auto filter feature. Auto filter chooses the best selection of filter based on the sample rate chosen.

This means that as you play different sample rates the appropriate filter is automatically chosen.

Polarity inversion

One of the handiest features on the PWD Mark II that will see a great deal of use is the polarity (phase) control. This touch screen option (available on the remote as well) allows users to select normal or inverted phase for every input and for every performance.

Sources and music have no standard for absolute polarity, a fact easily demonstrated by switching polarities on the as the music plays. Many Audiophiles mark their discs in phase and out of phase and are very careful to select the proper phase before playing each disc.

Some CD players and sources themselves invert phase so that a disc you believe is inverted actually is correct played on a specific device and incorrect on yet another. To fix this problem you can assign each input on the PWD Mark II to switch to the proper polarity when you activate that input. Touching this control is the same thing as reversing the loudspeaker connections of both loudspeakers (+ to -) at either the amplifier or speakers.

All live acoustic music is in absolute phase but some recordings may accidentally be made inverted and should sound more realistic and pleasant when you correct their phase with the switch.

Physical

 
Unit Weight 22 lbs [13.5 kg]
Unit Dimensions 14 x 17 x 4 [ 36cm x 43cm x 10cm]
Shipping Weight 31 lbs [19 kg]
Shipping Dimensions 20.5x 24 x 10 [52cm x 61cm x 25cm]

Power requirements

 
Input Power Model specific 100VAC, 120VAC, or 230VAC 50 or 60Hz
Power Consumption 30W
   

Digtial audio inputs

I2S (2), Coax, XLR Balanced, TOSLINK, USB

Sample Rates

I2S,S/PDIF, and USB -- 44.1kHz to 192kHz 16bit, 24bit
TOSLINK 44.1kHz to 96kHz 16bit, 24bit

Analog Audio Output

 
Connector RCA/XLR Unbalanced /Balanced (X2)
Output level, nominal 
(@ rated cartridge input)
1.0 VRMS (0dBV)/2.0 VRMS (+6dBV)
Output level, maximum 3.15 Vrms (+10dBV)/6.3 VRMS (+16dBV)
Output Impedance 100?/200?

Frequency Response

 
THD (5.0) 0.03%
(Balanced, +6dBV, 1KHz)
Signal to Noise Ratio 120dB 
(Balanced output, referenced to +6dBV nominal output level A Weighted)
Format PCM
Sample rate (PCM) 44.1kHz, 48.0kHz, 88.2kHz, 96.0kHz, 176.4kHz, 192kHz
Word length (PCM) 16b, 18b, 20b, 24b
$1,099.00
BUY NOW

Sprout is the culmination of PS Audios 42 years experience building concert quality audio products. We hand selected the best parts of that rich history and put it into a single, simple, easy-to-use personal music system. Its e...

Features
Tech Specs
  • Full featured integrated amplifier
  • 50 watts per channel power amplifier
  • Drives any size loudspeaker
  • Analog preamplifier
  • 192/24 high end fully asynchronous DAC
  • Passive EQ moving magnet phono preamplifier
  • Low output impedance headphone amplifier
  • Coaxial digital input
  • USB input
  • Analog Input
  • Built in Bluetooth receiver uses Sprouts internal asynchronous DAC
  • True analog stepped volume control
  • Analog input selector for all inputs
  • Headphone output 16? 500mW, 300? 425mW (drives all headphones)
  • Analog output: variable 3.5mm line, for subwoofer or otherwise
  • Signal-to-Noise Ratio (A-weighted) >90dB
  • THD <0.025% at normal listening levels
  • Dimensions: 6?W x 8?L x 1.75?H
$2,999.00
BUY NOW

The PowerPlay 8500 is easy to setup and does not require a fixed IP address or setup hassles of any kind as is common with some web addressable power conditioners. With PowerPlay you simply plug it into an Internet enabled network...

Features
Tech Specs
$8,349.00
BUY NOW

ThePerfectWave CD/DVD Memory player is a ground-breaking product that removes all digital sound limitations retrieving everything from your CD collection without any jitter or sonic loss. The PWT plays both standard and high re...

Features
Tech Specs

High resolution audio on DVD

The future of audio is to be found in higher resolution media than CDs which are limited to 44 kHz and 16 bits. The PWT can certainly play standard CDs directly but because the PWT is a high resolution audio transport, it can also read WAV files directly off a DVD and present jitter-free digital music to your DAC with resolution up to 24 bit and samples rates as high as 192 kHz.

High resolution downloads from sites like HD Tracks can easily be converted from FLAC or ALAC to WAV files on your computer, transferred to a DVD and played in all their high resolution glory on the PWD.

Cover art and song titles

Building the perfect transport means more than just producing the perfect output. The transport should also be a joy to use and answer a higher level of expectation from its owners.

60 years after the introduction of the vinyl LP, there are still very few players that recognize and display cover art and song titles from the disc itself. Once connected to an internet capable network connection, the PWT will display the cover art and song titles of just about any CD you place into it.

Imagine how much closer to the music youll find yourself with the picture of the artist on your player.

Every time you play a disc in your PWT a copy of the cover art and song titles are kept for you on your own private library page, accessed through our website. From your personal page on our website it is a simple matter to correct any of the CDs information, change cover art and polish your CD collection.

Asynchronous audio

The PWTs CD/DVD read device is a DVD ROM drive like that in a computer. This type of optical drive allows the PWT to read the music on the disc using an entirely different approach than that of a traditional transport or CD player.

To get bit perfect results without traditional error correction the PWT uses a multiple read technique which reads the data on the disc until its verified as bit perfect. Once confirmed as perfect it is then added to the Digital Lens memory.

Once in the Digital Lens solid state memory there is no clock information attached to it – just the raw and pure music extracted from the disc.

The output of the Lens is then forwarded to the PWT output through a fixed high precision, low jitter asynchronous clock. The PWT is one of the few true asynchronous transports in the world.

What does this mean to you? Better sound in fact, far better sound. Gone are the digital artifacts we become so used to. With the Memory Player you hear every detail on your disc and thats a revelation for many.

I2S through HDMI output

There are two ways to get the digital audio data out of the PWT: S/PDIF or I2S HDMI. I2S is the preferred method if you have the PS Audio PerfectWave DAC or any manufacturers DAC that can receive it.

S/PDIF (and AES/EBU) are the standard delivery methods and available on the PWT but are not the best sounding ones.

Standard digital outputs take three separate internal clocks along with the raw music data and combine them into one stream to the DAC. This mashup of music and clocks causes the audio to sound flat and harsh compared to I2S and is one of the reasons we designed NativeX on the PWD. NativeX eliminates many of the problems associated with S/PDIF.

A much better way of delivering the music is what I2S does and the audible results are stunning. Simply use any HDMI cable between the PWT and the DAC and you are transferring data perfectly, through I2S.

A growing number of DACS and devices are adopting the PS Audio HDMI standard for digital audio transmission because of its superior audio quality.

Digital Lens inside

Inside the PWT there is a built-in Digital Lens that stores the music from your disc before playing it. Unlike other approaches it is unnecessary to play the entire disc and place it into memory before listening. Instead, the intelligent Digital Lens stores only what is needed for perfect playback and the user experience is nearly instantaneous.

Just push play as you would on any CD player and the PerfectWave Memory Player does the rest instantly.

If you wish to see the lens in action, simply eject the disc while youre listening and note how the music continues to play even when the disc has been removed from the PWT .

It is the fact that you are listening to the stored version of whats on the disc that helps the music sound so lifelike and spacious. CD players all stream music directly off the CD while a PerfectWave Memory Player always plays out of its memory; never the disc.

The net results of this technology breakthrough is stunning sound perhaps for the first time on your system. Music played on the PWT is simply breathtaking, full, spacious and alive as no other player can do.

$6,499.00
BUY NOW

The P5 produces pure and perfect AC and is the power source of choice for almost any size system. Smaller than the P10, this workhorse of a product should be the foundation on which you build your system when a P10 isn't in the ca...

Features
Tech Specs
  • 1250 VA output
  • Built in Boulder
  • Surge protection
  • Spike protection
  • Regulated output voltage
  • Ten times lower distortion
  • Whisper cooling fan
  • 100% regenerated AC
  • Integrated oscilloscope
  • THD meter
  • Control over the web or network
  • Adjustable output voltage
$8,799.00
BUY NOW

The largest and most advanced high-end personal power generating station in the world. Capable of powering any size system with pure sine wave power, no other product comes close to a P10's ability to bring forth all that's possib...

Features
Tech Specs
  • 1500 VA output
  • Built in Boulder
  • Passively cooled
  • 100% regenerated AC
  • Integrated oscilloscope
  • THD meter
  • Control over the web or network
  • Adjustable output voltage
  • Color touch screen
$2,079.00
BUY NOW

Good things come in small packages and that is certainly the case with the NuWave DAC. Introducing PS Audio's most affordable D to A Converter. ...

Features
Tech Specs
  • Three digital inputs
  • 192kHz asynchronous USB
  • RCA and XLR balanced outputs
  • High current class A output stage
  • Native mode
  • 192kHz selectable upsample
  • Low jitter PerfectWave clocks
  • Class A fully balanced discrete analog electronics
  • Burr Brown 24 bit DAC chip

The NuWave DAC handles USB, single ended and optical digital audio up to 192kHz 24 bits and features a fully discrete output stage and remarkably sound qualit

$9,699.00
BUY NOW

Pure 100% DSD based D to A Converter Resolution perfect volume and balance controls built in Upsamples PCM and DSD to 10x DSD rate Purely passive transformer coupled output Improves imaging and soundstage Simple, direct signal pat...

Features
Tech Specs
  • Pure 100% DSD based D to A Converter
  • Resolution perfect volume and balance controls built in
  • Upsamples PCM and DSD to 10x DSD rate
  • Purely passive transformer coupled output
  • Improves imaging and soundstage
  • Simple, direct signal path with one master clock
  • Hand written filters, processors and upsamplers
  • Immune to incoming jitter problems from different sources
  • Increased digital headroom
  • No off-the-shelf IC DAC chips used
  • Uncovers musical details masked by typical PCM based processors
  • 7 digital inputs
  • Fully balanced from input to output
  • Color touch screen
$799.00
BUY NOW

Ten individually hand wired Power Port outlets, three isolated zones and all available at a price you can afford.  Filtration is handled through large core high permeability magnetic devices wound with heavy gauge OFC providi...

Features
Tech Specs
  • 3 isolated zones
  • 10 receptacles
  • Individually hand wired outlets
  • Common and differential mode filtering
  • Over/under voltage protection
  • Surge protection
  • Spike protection
  • Handles an entire system
  • Dimensions 15 x 6 x 2
$679.00
BUY NOW

AC power is a critical element in any high-performance audio/video system. Delivering that power to your equipment, without loss, is the job of the AC power cable.      The PerfectWave AC5 is the best value power...

Features
Tech Specs
$409.00
BUY NOW

The PerfectWave AC3 is PS Audio's most affordable power cable. The AC3 is a 12 gauge cable constructed with OFC copper in multiple gauges and shapes. Inside the AC3 is one OFC hollow conductor for the treble region, a larg...

Features
Tech Specs
  • Oxygen Free Copper (OFC)
  • 12 gauge power cable
  • Single shielded
  • Hollow tube conductors for treble performance
  • Rectangular conductors for midrange performance
  • Multiple gauge conductors for bass performance
  • Nickel plated connectors
  • Welded connector to conductor
$1,419.00
BUY NOW

PCOCC single crystal construction 8 gauge power cable Quad shielded Hollow tube conductors for treble performance Rectangular conductors for midrange performance Multiple gauge conductors for bass performance Gold plated connector...

Features
Tech Specs
  • PCOCC single crystal construction
  • 8 gauge power cable
  • Quad shielded
  • Hollow tube conductors for treble performance
  • Rectangular conductors for midrange performance
  • Multiple gauge conductors for bass performance
  • Gold plated connectors
  • Welded connector to conductor


View the entire catalogue >>